Autoplay
Autocomplete
Previous Lesson
Complete and Continue
2024-07 GCC Factories Plant Engineering Pre-Exam Revision
GETTING STARTED
START HERE
About the Pre-Exam Revision (9:23)
How to use the Learner management System (5:46)
How to get help from Palucraft?
Plant engineering exam questions (11:52)
Exam preparation strategy (1:52)
Can you claim ECSA CPD points? (7:35)
How to access the session recordings?
About the Palucraft Study Material
Download steam tables
Class Live Recordings
Day One (188:36)
Day Two (198:36)
Day Three (201:04)
Day Four (200:23)
Day Five (174:06)
DAY ONE (14 OCT 2024, 6 PM TO 9 PM)
Code of Good Practice on the Prevention and Elimination of Harassment in the Workplace
Substation explosion
Emerging psychosocial work hazards
Physical agent regulations 21 Oct 2022
Steam generator question insights (4:06)
Steam generator basics (16:23)
Class Example - Dryness fraction, enthalpy, specific volume (80:12)
November 2023 exam discussion and insights to upcoming exams (35:57)
Day 1 homework questions
June 2024 Suggested Answers
J24-Q2.2 - Transformer maintenance
J24-Q3 - ISO 45001 and Safety Management
J24-Q4.1 - Generator voltage and power
J24-Q4.2 - Vacuum Breaker Maintenance
J24-Q5.1 - Poiseuille pressure drop
J24-Q6.1 - Induction motor calculation
J24-Q6.2 - Variable speed drive benefits
J24-Q8.1 - Belt drive power and torque
J24-Q8.2 - Feeder sending off voltage and power factor
DAY TWO (14 MAY 2024, 6 PM TO 9 PM)
Conjugate explanation
Day 2 Homework Questions
June 2023 exam summary and upcoming exam insights (15:11)
Transformer question insights (2:37)
Transformer example - Calculate voltage and efficiency (75:06)
Transmission line example - Nominal Pi method (86:37)
Transmission line question variation to attempt
DAY THREE (15 MAY 2024, 6 PM TO 9 PM)
Day 3 Homework Questions
November 2022 exam review (10:44)
Motor insights (2:54)
Transmission line nominal T method example (50:42)
Synchronous motor example (70:59)
Motor input example (22:32)
DAY FOUR (16 MAY 2024, 6 PM TO 9 PM)
Day Four Questions
SANS 10142 review and insights (1:24)
Rotating equipment review and insights (4:12)
OHSMS and safety review and insights (19:04)
Venturi example (38:32)
June 2022 exam review and insights (21:23)
Compressor example (53:37)
Slurry example (67:59)
DAY FIVE (17 MAY 2024, 6 PM TO 9 PM)
Class Five Homework Questions
Shrink fit example (110:50)
Nov 2021 exam review and insights (12:28)
Thin-walled pressure vessels (19:43)
Strength of materials review and insights (6:25)
Popular SANS 10142 questions and answers
Section 6 - Installation requirements
Annexure I - SPDs for LV protection
Section 5 - Fundamental requirements
Annexure K - Earthing arrangements
Annex B - MV installation safety report
Annexure F - Conduit sizing
Section 8 - verification and certification
Section 3 - Definitions
Section 7 - Special installation or locations
Popular ISO 45001 questions and answers
BONUS - Possible ISO 45001 exam questions and solutions
TRANSFORMER ADDITIONAL HOMEWORK QUESTIONS
Transformer Practice Questions
Transformer Question 1 Solution
Transformer Question 2 Solution
Transformer Question 3 Solution
Transformer Question 4 Solution
Transformer Question 5 Solution
Transformer Question 6 Solution
Transformer Question 7 Solution
Transformer Question 8 Solution
Transformer Question 9 Solution
Transformer Question 10 Solution
ADDITION INDUCTION MOTORS HOMEWORK QUESTIONS
Induction Motors practice questions
Induction motor Q1 Solution
Induction motor Q2 Solution
Induction motor Q3 Solution
Induction motor Q4 Solution
Induction motor Q5 Solution
AC and DC GENERATOR ADDITIONAL HOMEWORK QUESTIONS
Alternators summary slides
AC and DC generator practice questions
AC and DC generator Question 1
AC and DC generator Question 2
AC and DC generator Question 3
AC and DC generator Question 4
OHS SAFETY MANAGEMENT SYSTEM ADDITIONAL PRACTICE
0 Introduction
1 Scope
3 Terms and definitions
4 Context of the organisation
5 Leadership and worker participation
6 Planning
7 Support
8 Operation
9 Performance evaluation
10 Improvement
Additional Motors Questions and Answers
Motor Questions
Motor Question 1 Solution
Motor Question 2 Solution
Motor Question 3 Solution
Motor Question 4 Solution
Motor Question 5 Solution
Motor Question 6 Solution
Motor Question 7 Solution
Additional Fluid Mechanics Questions and Answers
Q1: Flow rate using manometer
Q2: Slurry
Q3: Affinity Laws
Q4: Pump sizing
Q1: Compressor delivery temperature
Q2: Compressor work, temperature, pressure, efficiency
NEXT STEPS
Leave a review
Certificate of Completion
8 Operation
Lesson content locked
If you're already enrolled,
you'll need to login
.
Enroll in Course to Unlock